华为华三锐捷神码ac ap上线命令配置！

1. 在ap必须是瘦模式 2. 通过dhcp为ap下发ip和网关，顺带option 138 携带ac IP。 3. 或者在ap中配置acip，手动指定acip,为ap配置地址，静态路由，要与ac可达 如果你是已经建立好了集群，但是现在ap在备用ac上，你想切换到主ac上，在ap-config 配置模式下 通过命令 primary-base 修改ap的主ac即可进行强制切换。

H3C-AC间漫游用户接入AP控制配置举例

H3C-AC间漫游用户怎么接入AP控制，接入AP控制配置过程有什么要点，配置命令是什么?下面跟我一起来看看吧!

一、组网需求

两个无线控制器 AC 1 和AC 2 通过一个二层交换机连接，两个AC 处于同一个漫游组，客户端先通过AP 1 获取无线服务，然后漫游到与AC 2 相连的AP 2 上。要求客户端通过允许接入的AP 接入无线网络，并保证客户端在漫游后还能获取无线服务。

三、配置步骤

说明：radius服务的'配置参考其他，本省略

(1) 配置AC 1

# 配置AP 1。

system-view

[AC1] port-security enable

[AC1] dot1x authentication-method eap

[AC1] interface wlan-ess 1

[AC1-WLAN-ESS1] port-security port-mode userlogin-secure-ext

[AC1-WLAN-ESS1] port-security tx-key-type 11key

[AC1-WLAN-ESS1] undo dot1x multicast-trigger

[AC1-WLAN-ESS1] undo dot1x handshake

[AC1-WLAN-ESS1] quit

[AC1] wlan service-template 1 crypto

[AC1-wlan-st-1] ssid abc

[AC1-wlan-st-1] bind wlan-ess 1

[AC1-wlan-st-1] authentication-method open-system

[AC1-wlan-st-1] cipher-suite ccmp

[AC1-wlan-st-1] security-ie rsn

[AC1-wlan-st-1] service-template enable

[AC1-wlan-st-1] quit

[AC1] wlan ap ap1 model WA2100

[AC1-wlan-ap-ap1] serial-id 210235A045B05B1236548

[AC1-wlan-ap-ap1] radio 1 type dot11g

[AC1-wlan-ap-ap1-radio-1] service-template 1

[AC1-wlan-ap-ap1-radio-1] radio enable

[AC1-wlan-ap-ap1-radio-1] quit

[AC1-wlan-ap-ap1] quit

# 配置AC 1 上的漫游组，并使能IACTP 服务。

[AC1] wlan mobility-group abc

[AC1-wlan-mg-abc] source ip 10.18.1.1

[AC1-wlan-mg-abc] member ip 10.18.1.2

[AC1-wlan-mg-abc] mobility-group enable

[AC1-wlan-mg-abc] return

# 配置AP 组并应用在User Profile 下。

system-view

[AC1] wlan ap-group 1

[AC1-ap-group1] ap ap1 ap2

[AC1-ap-group1] quit

[AC1] user-profile management

[AC1-user-profile-management] wlan permit-ap-group 1

[AC1-user-profile-management] quit

[AC1] user-profile management enable

(2) 配置AC 2

# 配置AP 2。

system-view

[AC2] port-security enable

[AC2] dot1x authentication-method eap

[AC2] interface wlan-ess 1

[AC2-WLAN-ESS1] port-security port-mode userlogin-secure-ext

[AC2-WLAN-ESS1] port-security tx-key-type 11key

[AC2-WLAN-ESS1] undo dot1x multicast-trigger

[AC2-WLAN-ESS1] undo dot1x handshake

[AC2-WLAN-ESS1] quit

[AC2] wlan service-template 1 crypto

[AC2-wlan-st-1] ssid abc

[AC2-wlan-st-1] bind wlan-ess 1

[AC2-wlan-st-1] authentication-method open-system

[AC2-wlan-st-1] cipher-suite ccmp

[AC2-wlan-st-1] security-ie rsn

[AC2-wlan-st-1] service-template enable

[AC2-wlan-st-1] quit

[AC2] wlan ap ap2 model WA2100

[AC2-wlan-ap-ap2] serial-id 210235A22W0076000103

[AC2-wlan-ap-ap2] radio 1 type dot11g

[AC2-wlan-ap-ap2-radio-1] service-template 1

[AC2-wlan-ap-ap2-radio-1] radio enable

[AC2-wlan-ap-ap2-radio-1] quit

[AC2-wlan-ap-ap2] quit

# 配置AC 2 上的漫游组，并使能IACTP 服务。

[AC2] wlan mobility-group abc

[AC2-wlan-mg-abc] source ip 10.18.1.2

[AC2-wlan-mg-abc] member ip 10.18.1.1

[AC2-wlan-mg-abc] mobility-group enable

[AC2-wlan-mg-abc] quit

# 配置AP 组并应用在User Profile 下。

[AC2] wlan ap-group 1

[AC2-ap-group1] ap ap1 ap2

[AC2-ap-group1] quit

[AC2] user-profile management

[AC2-user-profile-management] wlan permit-ap-group 1

[AC2-user-profile-management] quit

[AC2] user-profile management enable

(3) 验证结果

AP 1 和AP 2 下的User Profile 均允许接入AP 1，AP 2，客户端漫游成功。

---